Home › RF Design Tools › Transmission Lines › Coaxial line
Coaxial Line Impedance Calculator
A coaxial line is an inner conductor, dielectric and outer conductor (ground) arranged concentrically, with the field fully enclosed — the most common interconnect in RF systems. Enter the dimensions to get impedance, L/C per length and delay, or synthesize the size for 50 Ω or 75 Ω.
Analyze d, D → ZoSynthesize D or dL, C per lengthDelay in ns/mTEM, no dispersion
How to use
- Enter the dielectric εr (PTFE 2.1, solid PE 2.25, air 1).
- Known dimensions: enter the inner diameter d and outer conductor inner diameter D and press Analyze for Zo, C, L, Vp and td.
- Designing for an impedance: enter the target Zo, then keep d and press Find D, or keep D and press Find d; the result is written into the D or d field.
Theory and formulas
Coax is a TEM line with the field entirely in the dielectric, so the formulas are exact:
Zo = (60/√εr) · ln(D/d) Ω
C = 2πε0εr / ln(D/d) ≈ 55.556 · εr / ln(D/d) pF/m
L = (μ0/2π) · ln(D/d) = 200 · ln(D/d) nH/m
Vp = c/√εr ≈ 3×10⁵ / √εr km/s
td = √εr / c ≈ 3.33 · √εr ns/m
Synthesis: D = d · eZo√εr/60 d = D / eZo√εr/60
C = 2πε0εr / ln(D/d) ≈ 55.556 · εr / ln(D/d) pF/m
L = (μ0/2π) · ln(D/d) = 200 · ln(D/d) nH/m
Vp = c/√εr ≈ 3×10⁵ / √εr km/s
td = √εr / c ≈ 3.33 · √εr ns/m
Synthesis: D = d · eZo√εr/60 d = D / eZo√εr/60
Design tips
- Common D/d ratios: for 50 Ω, PTFE (εr 2.1) ≈ 3.35, solid PE (2.25) ≈ 3.49, air ≈ 2.30; for 75 Ω solid PE ≈ 6.52.
- Air coax has minimum loss near 77 Ω and maximum power handling near 30 Ω; 50 Ω is the compromise that became the RF standard.
- D is the outer diameter of the dielectric (inner surface of the outer conductor), not the cable jacket diameter.
- Stay below the first higher-order mode: fc ≈ c / [ π(D + d)/2 · √εr ]; above it the TE11 mode can propagate.
FAQ
- Why are coax cables mostly 50 Ω or 75 Ω?
- 75 Ω is close to the minimum-loss point of air coax and is used for TV and video; 50 Ω balances power handling and loss for RF communication and test.
- What is the delay td used for?
- It converts cable length into phase and time delay — e.g. feed-line compensation in phased arrays, or locating a fault from a TDR time reading.
- Synthesis changed my D or d field?
- Yes. The synthesized dimension is written into the D or d field, and C, L, Vp and td update together.
Related design tools
Designing an RF product? WENSHING supplies RF transceiver modules, LoRa modules, SMD ceramic antennas, directional antennas and UHF RFID readers, and supports custom RF circuit design.
Contact an engineer