中文
English
Home > Products > Wireless RF Module> ASK RF Receiver > 123MHz Separate-Channel ASK Receiver Module, 4.6mm Thin | Clear of Crowded 315/433 Bands for Plant Data Links

123MHz Separate-Channel ASK Receiver Module, 4.6mm Thin | Clear of Crowded 315/433 Bands for Plant Data Links

Model:
RWS-123B

A 123MHz ASK receiver module that stays clear of the crowded 315/433MHz remote-control bands, so even when lots of remotes are being pressed nearby, none of them compete for its channel. It suits wireless data links inside a plant, and remote-controlled equipment that must not be set off by neighbors' remotes. The module is only 4.6mm thick.

Its output is standard CMOS/TTL logic that a microcontroller can read directly. Sensitivity is −106dBm and the data rate is 4.8kbps, which suits status, sensor and button data. It runs on 4.9–5.1V at a typical 4.5mA, measures 43.2×9.8×4.6mm and has 8 through-hole pins. Pair it with a 123MHz transmitter module. To work with ordinary off-the-shelf remotes, use a 315/433MHz receiver module instead.

A 4.6mm thin receiver working at 123MHz, away from the crowded 315/433MHz remote bands. Plenty of remotes pressed nearby will not compete for its channel.

ASK receiver module|Key characteristics

  • Its own channel
    123MHz avoids the crowded 315/433MHz remote bands.
  • Direct to logic
    Standard CMOS/TTL logic output, read directly by an MCU.
  • Thin
    43.2 × 9.8 × 4.6 mm fits tight housings.
  • Low power
    Typical 4.5mA on 5V.

Where it is used

Wireless data inside plants

Where many 433MHz remotes operate, data links move to 123MHz without interference.

Remote control on a separate channel

Remotes of neighbors and nearby shops will not trigger your equipment.

Data between PCs or controllers

Low-rate sensor and status data travel over one radio link without cabling.

Wiring and mounting

  1. 1Pick a 123MHz transmitter module for the sending end.
  2. 2Solder the receiver on the board and power it at 5V.
  3. 3Attach a suitable wire or external antenna to the antenna pin and the data pin to the MCU.
  4. 4Send a few messages at working distance and check the content is received correctly.

How to choose

Choose by band and use:

Avoid 315/433MHz with a separate channel
This 123MHz receiver
Pair with ordinary 315/433MHz remotes
Super-regenerative or superheterodyne receiver
Two-way data at higher speed
RF transceiver module
Thin, on 433MHz
Thin receiver with RSSI

The module only receives; 123MHz transmitter modules can be ordered from us.

Tell us the data volume, link distance and housing space, and we will match 123MHz transmitter and receiver.

FAQ

Q:Can ordinary remotes pair with it?

Most remotes are 315/433MHz; this needs a 123MHz transmitter, which we can supply.

Q:How long should the antenna be?

123MHz has a longer wavelength, so the wire is longer; tell us your housing space and we will suggest a length or external antenna.

Q:Is the data rate enough?

4.8kbps suits status, sensor and key data; for large amounts of data use an RF transceiver module.

▼ Specifications, product views and downloads follow below

123MHz ASK SUPERREGENERATIVE RECEIVER
RWS-123B 123MHz ASK Superregenerative RF Receiver Module — CMOS/TTL Data Output

RWS-123B is a 123 MHz ASK high-sensitivity receiver with −106 dBm sensitivity and 4.8 kbps data rate; its output drives any standard CMOS/TTL logic. A 4.6 mm low-profile board and low current make a quick wireless data link with the TWS-123 transmitter.

123 MHzOperating frequency
−106 dBmSensitivity
4.8 kbpsData rate
4.6 mmLow-profile height
RWS-123B 123MHz ASK RF receiver module

Why RWS-123B

Dedicated 123 MHz band

Stays clear of the crowded 315 / 433 MHz remote bands — useful where a separate channel is needed.

High −106 dBm sensitivity

High-sensitivity design with 1 MHz bandwidth demodulates weak signals reliably.

Direct CMOS / TTL output

Data can be handled directly by an MCU or encoder device and connects to any standard CMOS/TTL logic.

4.6 mm low profile

43.2 × 9.8 × 4.6 mm footprint fits slim enclosures.

Low current

Easy to operate with low consumption: 5 V supply, 4.5 mA typical.

Standard 8-pin SIP

2.54 mm pitch through-hole pins solder directly to the main board or plug into a header for easy service.

System Integration

RWS-123B Receiver system architectureA remote transmitter sends a 123MHz ASK/OOK signal; RWS-123B demodulates it and outputs digital data to a decoder IC or MCU, which drives a relay or load.ASK/OOKDATA OUTTXRemote transmitterTWS-123THIS RECEIVERRWS-123B123MHz · ASK/OOKMCUDecoder IC / MCUaddress match · decodeOUTPUTRelay · Loaddoor · motor · alarmRECEIVER SYSTEM ARCHITECTURELEGENDTHIS PRODUCTRF LINKDATA OUT
RWS-123B 123MHz RF receiver module dimension drawing 43.2 × 9.8 mm
  1. Pair with the WENSHING TWS-123 transmitter (123 MHz) to build the link.
  2. Feed VCC from a stable 5 V supply with a 100 nF decoupling capacitor; tie GND to system ground.
  3. Connect a wire or PCB antenna to ANT, away from digital traces and metal housings.
  4. Wire Digital Output directly to a CMOS/TTL input of your MCU or decoder.
  5. Let the MCU parse the data and drive relays, displays or alarm outputs.
RWS-123B pin assignment (8 pins, 2.54 mm pitch)
PinNameFunction
1GNDGround
2Digital OutputDemodulated data output (DATA)
3Linear OutputLinear (analog) output
4VCCSupply input
5VCCSupply input
6GNDGround
7GNDGround
8ANTAntenna input

RWS-123B Specifications

RWS-123B 123MHz ASK RF receiver module specifications
RF
Receiver architectureSuperregenerative, LC resonator
ModulationASK (OOK)
Operating frequency123 MHz
Sensitivity−106 dBm
Channel width±500 kHz (1 MHz bandwidth)
Data rate4.8 kbps
Receiver turn-on time≤ 3 ms
Interface
Data outputDigital output, demodulated data
Output high levelVcc − 0.5 V to Vcc (I = +200 µA)
Output low level≤ 0.3 V (I = −10 µA)
Logic compatibilityStandard CMOS / TTL
Power
Supply voltage4.9–5.1 V (5 V typ.)
Supply current4.5 mA (typ.)
Mechanical
Dimensions43.2 × 9.8 × 4.6 mm (L × W × H)
Pins8 through-hole pins, 2.54 mm pitch

Specifications are subject to the WENSHING datasheet.

RWS Superregenerative Receiver Family

WENSHING ASK superregenerative RF receiver module family (RWS series)
ModelHow to identifyFrequencySensitivitySupplyCurrentData rateSize (mm)Matching transmitter
RWS-371FGreen PCB, yellow tuning coil303.875–433.92 MHz (6 versions)−108 dBm3.8–5.5 V4.5 mA4.8 kbps43.2×10×7.5TWS-BS / DS / HS / FS
RWS-371Green PCB, red tuning coil303.875–433.92 MHz (6 versions)−108 dBm4.9–5.1 V4.5 mA4.8 kbps43.2×10×7.5TWS-BS / DS / HS / FS
RWS-374Green PCB, red coil + choke303.875–433.92 MHz (6 versions)−108 dBm4.9–5.1 V4.5 mA4.8 kbps43.2×10×7.5TWS-BS / DS / HS
RWS-375Blue PCB, yellow tuning coil303.875–433.92 MHz (6 versions)−108 dBm4.9–5.1 V4.5 mA4.8 kbps43.2×10×7.5TWS-BS / DS
RWS-123BBlue PCB, low profile123 MHz−106 dBm4.9–5.1 V4.5 mA4.8 kbps43.2×9.8×4.6TWS-123

The identification column is based on the actual product photos; electrical data is taken from each model page.

RWS-123B FAQ

Which transmitter should be used with RWS-123B?
Use the WENSHING TWS-123 transmitter, also on 123 MHz — transmitter and receiver frequencies must match.
How does RWS-123B differ from the RWS-371 series?
RWS-123B works at 123 MHz with −106 dBm sensitivity, only 4.6 mm high, with CMOS/TTL-compatible output; the RWS-371 series offers six remote-control versions from 303.875 to 433.92 MHz with −108 dBm sensitivity.
What does the module output? Do I still need a decoder?
The module demodulates the ASK/OOK RF signal into digital data on the Digital Output pin. Address and key information are decoded by a decoder IC or your MCU — connect DATA to a GPIO or interrupt pin and decode in firmware.
Any PCB layout tips?
Place a 100 nF decoupling capacitor close to VCC/GND and use a clean supply. Keep the antenna feed short and away from digital lines, and keep a solid ground — this minimises noise and preserves range.
Are samples or custom frequencies available?
Samples for evaluation and volume supply are available. Special frequencies or adaptations to your enclosure can be engineered on request — please contact our sales engineers.

Build reliable remote reception with RWS-123B

WENSHING has designed and manufactured RF modules in Taiwan since 1999 — transmitter/receiver pairing advice, samples and volume supply.

Contact Our RF Engineers

Key specifications at a glance

ModelRWS-123B
Frequency123MHz
ApplicationWireless communication, Home appliances, Industrial control
Size43.2*9.8*4.6
Product categoryASK RF Receiver

Compare ASK RF Receiver models

RWS-123B 123MHz ASK Superregenerative RF Receiver Module and other models in the same WENSHING category — select a model to see its full details.

ProductModelFrequencyApplication
RWS-123B 123MHz ASK Superregenerative RF Receiver ModuleRWS-123B123MHzWireless communication, Home appliances, Industrial control
RWS-434LL 433.92MHz OOK High-Sensitivity Superheterodyne Receiver Module (RSSI)RWS-434LL433.92MHz
RWS-434N-LV 433.92MHz 3.0V Low-Voltage ASK/OOK High-Sensitivity Receiver ModuleRWS-434N-LV-2 / RWS-434N-LV-3 / RWS-434N-LV-6Wireless communication, Home appliances, Industrial control
RWS-434N 315/433.92MHz ASK/OOK High-Sensitivity Superheterodyne Receiver ModuleRWS-434N-2 / RWS-434N-3 / RWS-434N-6310MHz / 315MHz / 433.92MHzWireless communication, Home appliances, Industrial control
RWS-438 303.875–433.92MHz ASK Superheterodyne RF Receiver ModuleRWS-438-6433.92MHzWireless communication, Home appliances, Industrial control
RWS-371F ASK Superregenerative RF Receiver Module 315MHz/433MHz (3.8–5.5 V)RWS-371F-1 / RWS-371F-2 / RWS-371F-3 / RWS-371F-4 / RWS-371F-5 / RWS-371F-6303.875MHz / 310MHz / 315MHz / 318MHz / 418MHz / 433.92MHzWireless communication, Home appliances, Industrial control
RWS-371 ASK Superregenerative RF Receiver Module 315MHz/433MHz 5VRWS-371-1 / RWS-371-2 / RWS-371-3 / RWS-371-4 / RWS-371-5 / RWS-371-6303.875MHz / 310MHz / 315MHz / 318MHz / 418MHz / 433.92MHzWireless communication, Home appliances, Industrial control
RWS-374 ASK Superregenerative RF Receiver Module 315MHz/433MHzRWS-374-1 / RWS-374-2 / RWS-374-3 / RWS-374-4 / RWS-374-5 / RWS-374-6303.875MHz / 310MHz / 315MHz / 318MHz / 418MHz / 433.92MHzWireless communication, Home appliances, Industrial control
RWS-375 ASK Superregenerative RF Receiver Module 315MHz/433MHzRWS-375-1 / RWS-375-2 / RWS-375-3 / RWS-375-4 / RWS-375-5 / RWS-375-6303.875MHz / 310MHz / 315MHz / 318MHz / 418MHz / 433.92MHzWireless communication, Home appliances, Industrial control

Need help choosing? browse all ASK RF Receiver products or contact our engineers for specifications, samples or a quotation.

For procurement & tender teams

Separate-band receiver module purchase checklist: RWS-123B 123 MHz ASK receiver

OEMs, industrial-control makers and schools that want to stay off the crowded 315/433 MHz bands usually specify frequency, sensitivity, output logic, supply and size. The list compares each item with the RWS-123B. Items marked "Stated" are in the specifications on this page.

✔ Stated on this page

1. Common purchase-spec requirements vs. RWS-123B

Operating frequency✔ Stated
Typical wording: A specified frequency away from common remote bands
123 MHz.
Modulation✔ Stated
Typical wording: ASK/OOK
ASK (OOK on-off keying)
Receiver sensitivity✔ Stated
Typical wording: Sensitivity stated in dBm (for example −105 dBm or better)
−106 dBm; channel width ±500 kHz (1 MHz bandwidth).
Data output✔ Stated
Typical wording: Digital output to a decoder IC or MCU
Digital output compatible with standard CMOS/TTL; connects directly to an MCU or decoder input.
Matching transmitter and range✔ Stated
Typical wording: Matching transmitter or remote, and working range
Pairs with the WENSHING TWS-123 transmitter (also 123 MHz).
Supply voltage✔ Stated
Typical wording: Matched to the system supply (5 V, 3.3 V or battery)
4.9–5.1 V (5 V typical).
Operating current✔ Stated
Typical wording: Low current for always-on listening
4.5 mA typical.
Size and pinout✔ Stated
Typical wording: Outline size, pin count and pitch (for drop-in replacement)
43.2 × 9.8 × 4.6 mm low profile; 8-pin DIP, 2.54 mm pitch.

2. Applications: data and remote reception on a separate band

Wireless data links
With the TWS-123 transmitter it forms a 123 MHz data link that feeds demodulated data to the MCU.
Appliance and lighting remotes
A separate band reduces interference with other remotes.
Machine control on production lines
Receiver for wireless control of production machines with less cabling.
Separate-band wireless alarms
Receives sensor triggers to build an alarm system on its own band.

4. Choosing an ASK/OOK receiver module (series comparison)

ModelArchitecture & frequencySensitivitySupplyCurrentSize
RWS-371FSuper-regenerative; six versions 303.875–433.92 MHz−108 dBm3.8–5.5 V4.5 mA43.2×10×7.5 mm
RWS-371Super-regenerative; six versions−108 dBm4.9–5.1 V4.5 mA43.2×10×7.5 mm
RWS-375Super-regenerative; six versions; 80–120 m with TWS-BS/DS−108 dBm4.9–5.1 V4.5 mA43.2×10×7.5 mm
RWS-374Super-regenerative; six versions; also pairs with TWS-HS−108 dBm4.9–5.1 V4.5 mA43.2×10×7.5 mm
RWS-123B
this page
Super-regenerative; 123 MHz−106 dBm4.9–5.1 V4.5 mA43.2×9.8×4.6 mm
RWS-434NSuperheterodyne; 310 / 315 / 433.92 MHz−114 to −118 dBm3.5–5.5 V5.7–7.3 mA43.2×10.2×9 mm
RWS-434N-LVSuperheterodyne; 310 / 315 / 433.92 MHz−116 to −118 dBm3.0–5.5 V8.0–11.0 mA43.2×10.2×6.5 mm
RWS-438Superheterodyne; six versions−108 to −114 dBm4.8–5.5 V2.7–3 mA43.2×10.2×6 mm
RWS-434LLSuperheterodyne; 433.92 MHz; RSSI output−117 dBm (2500 bps)2.0–5.5 V5.6 mA (5 V)43.5×10.03×4.5 mm

Scroll the table sideways. Values are taken from each model page. The frequency must match the existing remote or transmitter; for sites with heavy interference, look at the superheterodyne models first.

4. Procurement FAQ

Q: Which transmitter should I use?
Use the WENSHING TWS-123 transmitter at 123 MHz; both ends must use the same frequency.
Q: How does it differ from the RWS-371 series?
The RWS-123B works at 123 MHz with −106 dBm and is 4.6 mm thick; the RWS-371 series covers 303.875–433.92 MHz at −108 dBm.
Q: Can the output go straight to an MCU?
Yes. The digital output is standard CMOS/TTL compatible.
Q: What should an integrator, OEM or school send us for a quotation?
Please send: quantity, whether TWS-123 transmitters are also needed, and the delivery date.

"Typical wording" summarises public procurement documents and comparable product specifications in Taiwan and abroad. Performance of the RWS-123B is as stated on this page and in the official datasheet.